Skip to content

After Landing and Taxi to Gate

This guide will explain the correct procedures after we have landed and vacated the runway and then taxiing to the designated gate.

Disclaimer

The level of detail in this guide is meant to get a FlyByWire A320neo beginner from the runway to the designated destination gate.

A beginner is defined as someone familiar with flying a GA aircraft or different types of airliners. Aviation terminology and know-how is a requirement to fly any airliner, even in Microsoft Flight Simulator.

Further reading: A320 Autoflight
Also, you will find many great videos on YouTube on how to fly the FlyByWire A32NX.
Check out the FlyByWire YouTube Channel as well: FlyByWire on YouTube


Prerequisites

Aircraft has vacated the runway completely and has been brought to a stop on the taxiway as per previous chapters.

Runway vacated

Download FlyByWire Checklist

Chapters / Phases

This guide will cover these phases:

  1. After Landing
  2. Taxi to Gate

1. After Landing

Situation:

  • Aircraft has vacated the runways completely and has come to a stop on the taxi way as per previous chapters.
  • Flaps and Ground Spoilers are still deployed.
  • ATC has been informed that we vacated the runway.

Simulation vs. Real Life

In real life, the A320 will have two pilots who can actually do things in parallel. Talking to ATC, taxiing the aircraft and doing the after landing tasks.

In the simulation we are typically alone, so it is perfectly fine to stop once we have fully vacated the runway and do these things one after the other.

ATC Tower will usually hand us off to ATC Ground, and they will give us taxi instructions for our destination gate. Write them down and read them back as usual, but you don't have to move immediately unless ATC explicitly tells you to. Online ATC understand that the after-landing- tasks do take some time.

Immediate steps after vacating the runway:

  • Set your radio frequency to the one assigned by ATC or the airport charts.

    EDDM ATC frequencies

    RMP Panel

  • Disarm the Speed Brake lever (Ground Spoilers) by pushing down on the lever.

    Spoiler armed and disarmed

  • Set your ENG MODE selector to NORM in case you set it to IGN/START before.

    Engine Mode Switch Norm

  • Retract your FLAPS to 0.

    Flaps 0

  • Set your TCAS to STANDBY.

    ATC & TCAS

  • Set your RADAR and Predictive Windshear System (PWS) to OFF.

    WX and PWS off

  • Start your APU by clicking the APU MASTER SW button, then the APU START button.

    APU Start

  • Turn ANTI ICE OFF if not required.

  • Set your exterior lights:

    • Set your NOSE light to TAXI.
    • Set RWY TURN OFF light to ON.
    • Set your STROBE lights to AUTO/OFF (If you are crossing a runway, keep them ON until you vacate the runway).
    • For LAND lights, you can choose to retract them or turn them off.

      After landing lights

  • Turn the brake fan (BRK FAN) on if you get a hot brakes ECAM warning.

    Hot Brakes Brake Fan on

  • Complete the After Landing checklist.

    After Landing Checklist

This concludes After Landing

2. Taxi to Gate

Situation:

  • Aircraft on taxiway directly after runway.
  • After Landing checklist is completed.
  • ATC Ground has given taxi instructions.

Taxiing

Make sure to also read the Taxi section of the Engine Start and Taxi chapter.

Use your charts to follow the ATC taxi instructions to the designated gate.

Crossing a Runway

When approved to cross a runway (active or not) perform the following actions:

  • Look out the windows and visually ensure that there are no visible aircraft to your left and right.
  • Turn on extra lights to ensure your aircraft is visible when crossing:
    • Strobe lights - Set to ON
  • Inform ATC you have vacated the runway if required.

Warning

Never cross a runway without express permission from ATC and providing a read back of said instructions. Always ensure maximum safety when crossing.

Turning into the Gate

When turning into the gate, turn off your NOSE light and your RWY TURN OFF lights to not blind the ground personnel. This, of course, is only done at this point if enough lighting is available to safely park into the gate.

Taxi lights off

This concludes Taxi to Gate

Continue with Powering Down


Last update: September 13, 2023